MM to Inches: Formula, Fraction Chart and Examples
Millimetres are the go-to unit for precise measurements: screws, drill bits, jewellery, camera lenses and phone thickness. Inches still rule hardware stores and plans in the US. Converting between them is exact: one inch is 25.4 millimetres.
Quick answer
- 1 mm = 0.03937 inches
- 1 inch = 25.4 mm (exact)
- Divide millimetres by 25.4 to get inches. Multiply inches by 25.4 to get millimetres.
The mm to inches formula
inches = millimetres ÷ 25.4
The inch has been defined as exactly 25.4 mm since 1959 (see NIST Handbook 44, Appendix C), so the result is as precise as your measurement.
Worked examples
- 5 mm ÷ 25.4 = 0.197 in
- 10 mm ÷ 25.4 = 0.394 in
- 12 mm ÷ 25.4 = 0.472 in
- 20 mm ÷ 25.4 = 0.787 in
- 50 mm ÷ 25.4 = 1.969 in
Millimetres to inches chart
| Millimetres | Inches (decimal) |
|---|---|
| 1 mm | 0.039 in |
| 2 mm | 0.079 in |
| 3 mm | 0.118 in |
| 4 mm | 0.157 in |
| 5 mm | 0.197 in |
| 6 mm | 0.236 in |
| 8 mm | 0.315 in |
| 10 mm | 0.394 in |
| 12 mm | 0.472 in |
| 15 mm | 0.591 in |
| 20 mm | 0.787 in |
| 25 mm | 0.984 in |
| 30 mm | 1.181 in |
| 40 mm | 1.575 in |
| 50 mm | 1.969 in |
| 75 mm | 2.953 in |
| 100 mm | 3.937 in |
| 150 mm | 5.906 in |
| 200 mm | 7.874 in |
| 300 mm | 11.811 in |
Inch fractions to millimetres
Tools, sockets and drill bits are often sized in fractions of an inch. This chart gives the exact metric equivalents.
| Fraction | Decimal inches | Millimetres |
|---|---|---|
| 1/16″ | 0.0625 | 1.59 mm |
| 1/8″ | 0.1250 | 3.18 mm |
| 3/16″ | 0.1875 | 4.76 mm |
| 1/4″ | 0.2500 | 6.35 mm |
| 5/16″ | 0.3125 | 7.94 mm |
| 3/8″ | 0.3750 | 9.52 mm |
| 7/16″ | 0.4375 | 11.11 mm |
| 1/2″ | 0.5000 | 12.70 mm |
| 5/8″ | 0.6250 | 15.88 mm |
| 3/4″ | 0.7500 | 19.05 mm |
| 7/8″ | 0.8750 | 22.22 mm |
| 1″ | 1.0000 | 25.40 mm |
How to convert inches to mm
millimetres = inches × 25.4. For example, 3/8″ = 0.375 × 25.4 = 9.525 mm, and 2.5″ = 63.5 mm.
Turning a decimal into the nearest fraction
Most US rulers are marked in sixteenths. Multiply the decimal part of your answer by 16 and round to the nearest whole number. For 10 mm: 10 ÷ 25.4 = 0.394 in, and 0.394 × 16 ≈ 6.3, so 10 mm is just over 6/16 (3/8) of an inch.
Tip for tools: metric and imperial sizes are rarely exact matches. A 10 mm socket (0.394″) is close to a 3/8″ socket (0.375″) but not the same, so using the wrong one can round off a bolt head.
Common mistakes
- Confusing mm and cm. 1 inch = 25.4 mm = 2.54 cm. If your answer is ten times too big or small, check the unit.
- Assuming close sizes are interchangeable. 6 mm (0.236″) isn’t quite 1/4″ (0.25″).
- Rounding too early. Keep three decimals in inches for anything that has to fit.
Frequently asked questions
How many mm are in an inch?
Exactly 25.4 millimetres.
What is 1 mm in inches?
About 0.0394 inches, a little more than 1/32 of an inch (0.03125″).
Is 1/4 inch the same as 6 mm?
Not quite. 1/4 inch is 6.35 mm. For loose fits they’re interchangeable; for precise parts they aren’t.
How do I measure millimetres without a metric ruler?
Measure in inches and multiply by 25.4. For example, a 1 1/2″ width is 1.5 × 25.4 = 38.1 mm.
